Home » Sponsored Content » Wire Cutting Vs Laser Cutting Vs Plasma Cutting

Wire Cutting Vs Laser Cutting Vs Plasma Cutting

Posted by: Zhou casting 2021-10-29 Comments Off on Wire Cutting Vs Laser Cutting Vs Plasma Cutting

With the development of science and technology, there are more and more cutting methods, such as: laser cutting, water cutting, plasma cutting, wire cutting…what is the difference between them?

Listen to an engineer in the cutting field say:

  • 1) At present, the mainstream fiber lasers in the market, carbon dioxide lasers are gradually eliminated, and the energy consumption is too high, and there is still a market in the non-metallic field.
  • 2) The price of optical fiber equipment has dropped drastically in the low- and medium-power range since the laser was made domestically.
  • 3) In addition to laser cutting methods, plasma and wire cutting are in high demand in the market, but wire cutting is targeted at more Mold industries. Plasma is in demand for thick plates or when the precision is not high. Waterjet cutting is now It is no longer common in the metal industry, and there are many in the non-metal field.
  • 4) In the future development, laser cutting is absolutely the world of thin metal plates, including non-metal cutting, laser cutting will occupy a considerable part of the market.

Next we analyze these several cutting technologies.

Laser Cutting

Optical cutting is the use of a focused high-power density laser beam to irradiate the workpiece to quickly melt, vaporize, ablate or reach the ignition point of the irradiated material. At the same time, the molten material is blown away by the high-speed airflow coaxial with the beam to realize the cutting of the workpiece. open. Currently, CO2 pulsed lasers are generally used, and china laser cutting is one of the thermal cutting methods.

Water Cutting 

Water cutting, also known as water jet, is a high-pressure water jet cutting technology, which is a machine that uses high-pressure water to cut. Under the control of the computer, the workpiece can be sculpted at will, and it is not affected by the texture of the material. Water cutting is divided into two methods: no sand cutting and sand cutting.

Plasma Cutting

Plasma arc cutting is a processing method that uses the heat of the high-temperature plasma arc to locally melt (and evaporate) the metal at the incision of the workpiece, and use the momentum of the high-speed plasma to remove the molten metal to form an incision.

Wire Cutting 

Wire Electrical Discharge Machining (WEDM), belongs to the category of electrical processing, sometimes also called wire cutting. Wire cutting can be divided into fast-moving wire cutting, medium-moving wire cutting, and slow-moving wire cutting. The wire speed of fast wire EDM wire cutting is 6-12 m/s, and the electrode wire moves back and forth at high speed, so the cutting accuracy is poor. Middle wire EDM is a new technology developed in recent years to realize the function of frequency conversion multiple cutting on the basis of fast wire wire cutting. The wire speed of slow wire EDM wire cutting is 0.2m/s, and the electrode wire moves in one direction at a low speed, and the cutting accuracy is very high.

The Comparison Of Application Range 

The laser cutting machine has a wide range of applications. Regardless of metal or non-metal, it can cut and cut non-metal, such as cloth, leather, etc. with CO2 laser cutting machine, and for cutting metal with fiber laser cutting machine. The deformation of the plate is small.

Water cutting is a cold cutting, no thermal deformation, good quality of the cutting surface, no secondary processing is required, and it is easy to perform secondary processing if necessary. Water cutting can perforate and cut any material, with fast cutting speed and flexible processing size.

Plasma cutting machine can be used to cut various metal materials such as stainless steel, aluminum, copper, cast iron, carbon steel, etc. Plasma cutting has obvious thermal effect, low precision, and it is not easy to perform secondary processing on the cut surface.

Wire cutting can only cut conductive materials, and cutting coolant is required during the cutting process. Therefore, materials that are not conductive, afraid of water, or afraid of contamination by cutting coolant, such as paper and leather, cannot be cut.

The Comparison Of Cutting Thickness 

The industrial application of laser cutting carbon steel is generally below 20mm. The cutting capacity is generally below 40mm. The industrial application of stainless steel is generally below 16mm, and the cutting capacity is generally below 25mm. And as the thickness of the workpiece increases, the cutting speed decreases significantly.

The thickness of water cutting can be very thick, 0.8-100mm, or even thicker materials.

The plasma cutting thickness is 0-120mm, and the best cutting quality range is about 20mm. The plasma system has the highest cost performance.

The thickness of wire cutting is generally 40-60mm, and the thickest can reach 600mm.

The Comparison Of Cutting Speed 

Using a laser with a power of 1200W to cut 2mm thick low-carbon steel plates, the cutting speed can reach 600cm/min; for 5mm thick polypropylene resin plates, the cutting speed can reach 1200cm/min. The cutting efficiency that can be achieved by wire EDM is generally 20-60 mm2/min, up to 300 mm2/min; obviously, the laser cutting speed is fast and can be used for mass production.

The water cutting speed is quite slow and not suitable for mass production.

The cutting speed of plasma cutting is slow and the relative accuracy is low. It is more suitable for cutting thick plates, but the end surface has a slope.

For metal processing, wire cutting has higher precision, but the speed is very slow. Sometimes other methods are needed to punch and thread to cut, and the cutting size is greatly limited.

The Comparison Of Cutting Accuracy 

The laser cutting incision is narrow, the two sides of the incision are parallel and perpendicular to the surface, and the dimensional accuracy of the cut parts can reach ±0.2mm.

The plasma can reach within 1mm.

Water cutting will not produce thermal deformation, and the accuracy is ±0.1mm. If a dynamic waterjet cutting machine is used, the cutting accuracy can be improved, and the cutting accuracy can reach ±0.02mm, eliminating the cutting slope.

The machining accuracy of wire cutting is generally ±0.01~±0.02mm, up to ±0.004mm.

The Comparison Of Slit Width

Laser cutting is more precise than plasma cutting, and the slit is small, about 0.5mm.

The slit of plasma cutting is larger than that of laser cutting, about 1-2mm.

The cutting seam of water cutting is about 10% larger than the diameter of the knife tube, generally 0.8-1.2mm. As the diameter of the sand knife tube expands, the incision becomes larger.

The width of the slit for wire cutting is the smallest, generally around 0.1-0.2mm.

The Comparison Of Cutting Surface Quality 

The surface roughness of laser cutting is not as good as water cutting, the thicker the material, the more obvious.

Water cutting will not change the texture of the material around the cutting seam (laser is a thermal cutting and will change the texture of the cutting area).

Production Input Cost Comparison

  • 1) Different models of laser cutting machines have different prices. Cheap ones such as carbon dioxide laser cutting machines cost only 20,000 to 30,000, and expensive ones such as 1000W fiber laser cutting machines now cost more than one million. Laser cutting has no consumables, but the equipment investment cost is the highest among all cutting methods, and it is not a little bit higher, and the use and maintenance costs are also quite high.
  • 2) Plasma cutting machine is much cheaper than laser cutting machine. According to the power and brand of plasma cutting machine, the price is different and the use cost is higher. Basically, as long as it can cut conductive materials.
  • 3) The cost of water cutting equipment is second only to laser cutting, with high energy consumption and high maintenance costs. The cutting speed is not as fast as plasma, because all abrasives are disposable, and they are discharged into the nature after they are used once. , The environmental pollution caused by this is also more serious.
  • 4) Wire cutting is generally in the period of 5000-30000 US dollars. However, there are consumables for wire cutting, such as molybdenum wire and cutting coolant. There are two kinds of wire commonly used in wire cutting. One is molybdenum wire (molybdenum is precious), which is used in fast-moving wire equipment. The advantage is that molybdenum wire can be reused many times; the other is copper wire (which is much cheaper than molybdenum wire anyway).了), used for slow wire walking equipment, the disadvantage is that the copper wire can only be used once. In addition, the fast-moving wire machine is far cheaper than the slow-moving wire machine. The price of a slow-moving wire is equal to 5 or 6 fast-moving wires.

Link to this article:Wire Cutting Vs Laser Cutting Vs Plasma Cutting

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting:https://www.cncmachiningptj.com/


Sheet metal, Copper Milling, carbon steel,online laser cutting service, 3D printing, precision CNC machining services for heavy equipment, construction, agriculture and hydraulic industries. Suitable for plastics and rare alloys machining. It can turn parts up to 15.7 inches in diameter. Processes include swiss machining,broaching, turning, milling, boring and threading. It also provides metal polishing, painting, surface grinding and shaft straightening services. The production range(include aluminum die casting and zinc die casting) is up to 50,000 pieces. Suitable for screw, coupling, bearing, pump, gearbox housing, drum dryer and rotary feed valve applications.PTJ will strategize with you to provide the most cost-effective services to help you reach your target,Welcome to Contact us ( [email protected] ) directly for your new project.

Link to this article:Wire Cutting Vs Laser Cutting Vs Plasma Cutting

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Casting Wiki,THANKS!^^